测绘学报 ›› 2023, Vol. 52 ›› Issue (2): 218-229.doi: 10.11947/j.AGCS.2023.20210565

• 摄影测量学与遥感 • 上一篇    下一篇

点-线特征联合的全景图像位姿解算方法

朱宁宁, 杨必胜, 陈驰, 董震   

  1. 武汉大学测绘遥感信息工程国家重点实验室, 湖北 武汉 430079
  • 收稿日期:2021-10-10 修回日期:2021-12-27 发布日期:2023-03-07
  • 通讯作者: 杨必胜 E-mail:bshyang@whu.edu.cn
  • 作者简介:朱宁宁(1988-),男,博士后,研究方向为摄影测量与遥感。E-mail:ningningzhu@whu.edu.cn
  • 基金资助:
    国家杰出青年科学基金(41725005);国家自然科学基金(42101446;42071451);测绘遥感信息工程国家重点实验室专项科研经费资助;中国博士后科学基金(2022T150488)

Position-attitude calculation of panoramic image based on point-line feature combination

ZHU Ningning, YANG Bisheng, CHEN Chi, DONG Zhen   

  1. State Key Laboratory of Information Engineering in Surveying, Mapping and Remote Sensing, Wuhan University, Wuhan 430079, China
  • Received:2021-10-10 Revised:2021-12-27 Published:2023-03-07
  • Supported by:
    The National Science Fund for Distinguished Young Scholars of China (No. 41725005);The National Natural Sciences Foundation of China (Nos. 42101446;42071451);LIESMARS Special Research Funding;China Postdoctoral Science Foundation (No. 2022T150488)

摘要: 目前,全景图像位置和姿态参数的解算多基于点特征,而场景中普遍存在的线特征尚未得到充分利用。本文提出一种点-线特征联合的全景图像位姿解算方法,不仅可用于点特征缺失场景中全景图像位姿参数的解算,而且在点特征充足的场景中可提高位姿解算的精度和稳健性。该方法中的线特征使用线上的任意两点表示,不要求全景图像和三维场景同名线上的选点具有对应关系,因而易于选取,具有极大的实用性。首先,使用直接线性变换构建点-线特征联合的全景图像位姿解算模型,并针对水平线和垂直线获取简化后的模型;然后,利用仿真道路场景,从特征点和线的不同组合方式及大姿态角两方面分析该模型的适用性,并通过人工引入不同类型及量级的点-线误差分析该模型的容差性;最后,将本文方法应用于全景图像与激光点云的融合,从理论和实践两方面证明点-线特征联合的位姿解算方法在精度、稳健性和容差性方面优于单纯的点特征解算方法。

关键词: 全景图像, 点-线特征联合, 位姿解算, 仿真分析, 全景图像与激光点云融合

Abstract: At present, the position and attitude parameters of panoramic images are mostly solved by point features, while the line features commonly existing in the scene have not been fully utilized. In this paper, a solution method based on point-line feature combination is proposed, which can not only be used to solve the position and attitude of panoramic image in the scene with missing point features, but also improve the accuracy and robustness in the scene with sufficient point features. The line feature in this method is represented by any two points on the line, which does not require the corresponding relationship between the panoramic image and the 3D scene, so it is easy to select and has great practicability. Firstly, the direct linear transform (DLT) is used to construct the point-line feature combination model of panoramic image, and the simplified model is obtained for horizontal and vertical lines; Then, using the simulated road scene, the applicability of the model is analyzed from the two aspects:different combinations of feature points and lines, large attitude angle, and the tolerance is analyzed by manually introducing different types and magnitude of point-line errors; Finally, this method is applied to the fusion of panoramic image and LiDAR points. It is proved that this method of point-line feature combination is better than the simple point method in accuracy, robustness and tolerance.

Key words: panoramic image, point-line feature combination, position and attitude calculation, simulation analysis, panoramic image and LiDAR points fusion

中图分类号: